We spent many hours on research to finding 1/3 hp yoke mount motor, reading product features, product specifications for this guide. For those of you who wish to the best 1/3 hp yoke mount motor, you should not miss this article. 1/3 hp yoke mount motor coming in a variety of types but also different price range. The following is the top 10 1/3 hp yoke mount motor by our suggestions
531 reviews analysed
1. Century formerly AO Smith GF2054 1/2 hp, 1725 RPM, 115 volts, 48/56 Frame, ODP, Sleeve Bearing Belt Drive Blower Motor
2. 1/3hp 1725RPM 48/56Frame 115 volts Belt Drive Furnace Motor Century # GF2034
3. GE – Genteq Evergreen 1/2 HP 230 Volt Replacement X-13 Furnace Blower Motor
4. A.O. Smith B2852 3/4 HP, 3450 RPM, 1 Speed, 230/115 Volts, 5.4/10.8 Amps, 1.25 Service Factor, 56Y Frame, PSC, ODP Enclosure Square Flange Pool Motor
5. New WEG 1.5HP Electric Motor Fan Pump Compressor General purpose 56 frame 3430 rpm 1 phase 115/230VAC
Description
1.5 hp – 56 Frame – 3430rpm – Single Phase – 115 / 208-230volt – 5/8″ shaft diameter – 1.874″ shaft length Please see attached Pics for motor dimensions and frame dimensions Technical Info: Horsepower: 1.5 Amperage: 8.40 fl amps at 230v Phase: One / Single Phase 2 pole Voltage: 115 / 208-230 RPM: 3430 Torque: 2.27lb.ft Base: Reinforced fixed base Frame: 56 Shaft Diameter: 5/8″ Keyed shaft Shaft Length: 1.874″ Rotation: Reversible CW or CCW Rotation Frequency: 60hz Service Factor: 1.00 @ 230v Enclosure: ODP Open Drip Proof (internally fan cooled) Construction: Rolled Steel Overload: Yes – Manual reset button Efficiency: (100%) 68.0 Weight: 40 lb
6. Century GF2024 1/4 For hp 1725 RPM 48 Frame 115V Belt Drive Furnace Motor
Description
Belt Drive Motor, Motor Application HVAC/R, Motor Sub Application Belt Dr Fan/Blower, Motor Type Split-Phase, HP 1/4, Nameplate RPM 1725, Voltage 115, Frame 48, Enclosure Open Dripproof, Mounting Cradle, Hz 60, Full Load Amps 5.4, Thermal Protection Auto, Insulation Class B, Service Factor 1.35, Bearings Sleeve, Max. Ambient Temp. 40 Degrees C, Rotation CW/CCW, Shaft Dia. 1/2″, Shaft Length 1-1/2″, Length Less Shaft 7-7/16″, Overall Length 8-15/16″, Body Dia. 5-5/8″, Resilient Ring Dia. 2-1/2″, Ring to Ring Center 7-3/16″, Nominal Efficiency 54.0%, Duty Continuous, RPM Range 1701-1800, Phase 1, Standards CSA Certified, Includes 5/8″ dia. Shaft BushingWARNING: California ResidentsThis product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
7. GE – Genteq Evergreen 1 HP 230 Volt Replacement X-13 Furnace Blower Motor
8. A.O. Smith GF2024 Century Resilient Base Split Phase Electric Motor, 115 Vac, 5.4 A, 1/4 Hp, 1725 Rpm
Description
Century Electric Motor, Resilient Base, Split Phase, Century, 115 VAC, 5.4 A, 60 Hz, 1/4 hp Power, Number of Phase: 1, 1725 rpm, 1/2 in Shaft Diameter, 1-1/2 in Shaft Length, Service Factor: 1.35, CW/CCW Rotation Type, Sleeve Bearing, Cradle Mounting, 1-3/8 in Mounting Hole Center, 54 % Efficiency, 40 deg C Ambient, Class B Insulation, Open Drip proof. Split phase motor, 5.4 amps, 60 hertz, auto protector, Sleeve Bearing, 1/2-Inch x 1-1/2-Inch shaft.
9. Motor, 1/3 HP, Yoke
10. NEW STEEL DRIVESHAFT,ANY LENGTH,27-64",WITH 32 SPLINE YOKE & U-JOINTS,STREET ROD
Feature
- Brand New Southwest Speed Steel Drive Shaft with a 32 Spline Yoke to fit the GM Transmissions listed below.
- Your choice of any length from 27″ to 64″ long, in 1/2″ increments.
- These lengths are measured center of u-joint cup to center of u-joint cup (2nd picture above), but we also have a way to measure them without having a current shaft.
- Includes new 32 spline yoke and 1310 series u-joints. Other yokes & conversion u-joints are available. Just ask before ordering for the price difference.
- These driveshafts have been used for years by some of the best race car & street rod builders in the country
Description
- Southwest Speed refers to these driveshafts as the ‘2 1/2″ Outside Diameter’ series of driveshafts; as they’ve continued to make them longer and longer, they’ve begin using larger diameter tubing on some of those longer shafts: At 50″, they step up to 2 3/4″, At 58″, they step up to 3″, At 60 1/2″, they step up to 3 1/2″.
- All have .065″ wall DOM tubing.
- Includes:
- New 32 spline transmission yoke. This yoke will fit any transmission with a 32 spline output shaft, including GM Turbo 400, T-400, TH-400, Richmond Super T-10 4 Speed, Muncie M21 4 Speed, Muncie M22 Rockcrusher 4 Speed,Doug Nash, Jerico, 4L80E, 4L85E, All GM Borg Warner, except T-4 & T-5
- Both front & rear new u-joints, which are 1 1/16″ diameter cups (Measurement C) by 3 7/32″ wide (Measurement B)
- On the rear of the driveshaft, these shafts will fit the 1310 rear end (or pinion) yoke.
- If you aren’t sure if this is the yoke you have, the easiest way to make sure is measure to see if the 1 1/16″ x 3 7/32″ u-joint will fit it.
- 2 Different Ways to Measure for the Length:
- Measuring your old driveshaft if it is available is the easiest way.
- Measure from the center of the u-joint cup to the center of the u-joint cup
- Using this measurement, we have every length from 27″ to 64″.
- If your old drive shaft isn’t available or this shaft will be installed in a new car, you can use this method.“A”-Measure from the rear of the tail housing on your transmission to the front of the rear end (or pinion) yoke.
- This measurement needs to be taken with the car at “ride height”; you cannot get a proper measurement with the car jacked up in any way.
- If you use this method to determine the length, just make sure to let us know at checkout that “the A dimension is ___”.
- Using this measurement, we have every length from 29″ to 67″ in stock.
Conclusion
By our suggestions above, we hope that you can found 13 Hp Yoke Mount Motor for you.Please don’t forget to share your experience by comment in this post. Thank you!